Staffordshire blue 'Classic' pavers
Square edged or chamfered
Inherent natural beauty & strength
Manufactured to the same specification for over 100 years, Ketley Staffordshire Blue Clay Pavers are the original product with a rich distinctive colour that is permanent. Made from the finest Etruria Marl fired at over 1130°, Ketley Pavers are of unrivalled strength and durability.
Case Studies
Wembley Way
The iconic approach to Wembley Stadium, known as Olympic Way or Wembley Way has undergone a recent transformation in a joint project by Brent Countil and Quintain Estates. The new scheme designed by Dixon Jones Architects has drawn on the heritage of the site, and uses over 200,000 Ketley Staffordshire blue 'Classic' chamfered pavers, laid in a herringbone pattern and interspersed with bands of granite. Full details
Redhill Town Centre
Redhill Town Centre This town centre regeneration with grey granite and Staffordshire Blue pavers created a new focal point within the town of Redhill. Liz Freemont, the landscape designer, used the contrasting materials to create distinct surfaces of movement and focus within the pedestrian area. Liz defined a new “Town Square” space by using Ketley Staffordshire Blue 'Classic' chamfered pavers laid in a running bond, with a light grey mortar and broke up this large area of blue clay pavers with small strips of granite. In the roads leading to this new square, she used the materials in reverse and as a result, a previously dull and indistinct space, has become a busy meeting place with proportion and prominence. Full details >>
Lowry centre Manchester
This ultra modern waterside arts complex was developed at the old Salford Quays in Greater Manchester. The overall design set out to reflect the surrounding landscapes and flourishing waterways of the docklands and Ketley's plain staffordshire blue 'Classic' chamfered pavers were chosen as their strong blue colour is representative of the the industrial heritage of the area. Full details >>
Paving in Napier, South Island, New Zealand
Taradale Shopping Centre in Napier, South Island is a boutique shopping destination centred around a traditional busy high street. The planners at Napier Town Centre have traditionally sourced their paving materials from Australia, but having seen Ketley's blue square edged pavers, they decided the blue colour would add a unique feel to this up-market area. The planners could not find anything similar in Australia and therefore after setting up a test site of the pavers, they specified Ketley for the 3600m2 area. Full details >>
Blue pavers, at a private estate
Ketley Staffordshire blue 'Classic' pavers are laid here alongside cobblestones to restore this courtyard in the Cotswolds.
Environmental
Place of Manufacture: Brierley Hill, UK
Environmental Management: 14001 Download Certificate
Quality Management : 9001 Download Certificate
Download the Ketley Quality and Environmental Policy
Life Cycle: BRE Global Certification in accordance with EN 15804:2012 Download Certificate
Energy: Cured in gas fired kilns to 1130o C
Raw materials: Etruria Marl Clay from our local quarry in Brierley Hill, sand
Lifespan: Ketley's bricks are the toughest and most durable bricks you can buy.
Recyclability: Can be crushed and used as aggregate and/or as an inert bulk fill
Packaging: We keep packaging to a minimum using wooden pallets and we do not shrink wrap our brick packs.
Find out more about Ketley's approach to sustainability
Click for the Brick Development Association infographic on Sustainability of Brick
See below the latest video about Sustainability of Brick from the Brick Development Association
Tech Spec
Staffordshire blue 'Classic' pavers Specification Sheet
Performance Standard: BS EN 1344:2013
Ketley Staffordshire blue pavers are produced at our works located in the heart of the Black Country. They have been made from our own Etruria Marl since Victorian times. Their unrivalled physical properties include their strength, durability and permanence of colour.
Work Size mm |
Pattern |
Pack Weight |
No per pallet |
Units/m2 Rigid with 10mm joint |
Units/m2 Flexible butt Jointed (3mm joint) |
215x102.5x50 |
Square Edged |
1300kg |
500 |
40 |
44 |
215x102.5x65 |
Square Edged |
1320kg |
400 |
40 |
44 |
200x100x50 |
Square Edged |
1150kg |
500 |
43 |
48 |
200x100x65 |
Square Edged |
1200kg |
400 |
43 |
48 |
200x100x50 |
Chamfered |
1150kg |
500 |
43 |
48 |
200x100x65 |
Chamfered |
1200kg |
400 |
43 |
48 |
|
|
|
|
||
Colour |
Staffordshire blue |
||||
Raw Material |
Etruria Marl Clay |
||||
Manufacture |
Extruded, Wirecut and fired above 1130 degrees C |
||||
Bulk Density |
2,300kg/m3 |
||||
Texture |
Dragfaced |
||||
Size, Tolerance |
BS EN 1344: 2013 |
||||
Size Range |
R1 |
||||
Mean Transverse Breaking Load |
T4 |
||||
Unpolished Slip/Skid Resistance |
U3 |
||||
Abrasion Resistance |
|
||||
Freeze/Thaw Resistance |
FP100 |
Fittings
Ketley Brick have a long history producing special bricks and pavers.
View our Paver Specials Gallery
Browse our paver specials range online
Our unique plant produces a traditional natural clay colours for both the Paver and Brick ranges. Because our squares, pavers and specials are fired together, our colours are consistent through the range.
Ketley Brick also offers a made to measure service for bespoke requirements, this is covered in the Special Shapes section.
Laying
Paver Laying
Clay pavers should be laid in accordance with BS 7533-3:2005+A1:2009.
For post laying care, download our guide here
Download industry guidance on paver cleaning here
It is useful to plan the layout of pavers before full scale laying begins. It may help to minimize the number of pavers that need to be cut. It will help to identify the likely sand surcharge needed in setting levels. It will also indicate the likely finished appearance and the standard of on-site workmanship.
Clay pavers should be laid by hand, commencing from a straight starting edge on the prepared bedding course. They should be laid slightly open to provide a finished joint width between pavers of approx 2-5mm beyond the edge protection nibs to permit infill and to minimise damage in compaction and subsequent use. Failure to do this may result in chipping of the clay pavers.
Ketley pavers can be supplied with or without nibs. (Please note the nibs are there for edge protection of the pavers and are not spacer nibs, therefore the nibs should not be used to determine the gaps between pavers). If deviation from the bond pattern does occur, the pavers can be adjusted to open the Joints to about 5mm. This process is known as gapping. A small percentage outside this figure will not affect paver performance.
When a 90° herringbone bond pattern is used, a string line should be set up at right angles to the starting edge, and a "nose" of paving can then be advanced along it. When laying 45° herringbone pattern the laying face should develop parallel to the starting edge.
-
Pavers should be selected from three or more packs to ensure a thorough mix. If stocks of new pavers have to be laid on new work, they should be stacked about one metre back from the leading laid edge.
-
As far as possible whole pavers should be used. Pieces of less than 1/3rd of a full paver should be avoided. Various items in the Ketley range of paver fittings overcome this problem. Infilling of boundaries and obstructions should be completed before vibration commences. Paver cutting should be carried out by a disc cutter, not by the use of a splitting machine or hammer and chisel.
It is important to check the pattern of pavers against string lines as work progresses and adjust as necessary.
Once a sufficient area of clay pavers has been placed, approximately 40m2 on larger sites, fine dry sand should be brushed into the joints.
After brushing into the joints, surplus sand should be brushed away before compaction begins. Pavers should then be compacted into position by two or three passes of a vibrating plate compactor fitted with a neoprene pad. As recommended in BS7533-3:2005, the plate area should be at least 0.20m2. it should transmit an effective force of 50-75 :kn/m2 at a vibration frequency of between 60-1OOHz. Compaction should not be performed closer than one metre from any unrestrained edge.
Further sand should then be applied and the procedure repeated. After final compaction 1-2mm of sand can be spread over the paved area to promote joint fitting and to fill any voids which may develop.
Commencement of use of the pavement may need to be delayed if the bedding course is saturated following heavy rain. During the early life of the pavement there is likely to be some settlement of sand within the joints. Therefore the site should be monitored and arrangements made for further sand to be brushed in, to top up the joints.
Instructions on how to lay for rigid construction can be found in our Clay Pavers and Fittings brochure (available here for download)
Cleaning
Paver Cleaning
Paved areas should be swept with a stiff brush on a regular basis, to remove dust and detritus that tends to accumulate, especially in sheltered corners, and around drains.
The paving should be inspected on a quarterly basis, looking for loose, damaged or stained paving, and checking that the joints are filled. Vacuum road sweepers should not be used during the early life of the pavement as they will remove the jointing sand. Other causes for loss of jointing sand include, erosion by exceptional surface water flow, the effects of high-powered engines or power-washers, action of ants or insects and loss due to movement of the paving.
In situations where an excessive amount of grime and dirt has built up, occasional steam cleaning should be carried out. Jointing sand levels should be checked after this operation and replaced as required.
Pavements in damp areas such as beneath trees and in permanent shade may develop unwanted weed or moss growth. Regular brushing will disrupt emerging weeds, a proprietary weed killer should be used which will have no detrimental effect on the pavers for more stubborn weeds. It is always wise to test the product to be used in a small area first.